ASTM International standards

A

• ASTM A1 Standard Specification for Carbon Steel Rails
• ASTM A6 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
• ASTM A29 Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements for
• ASTM A36 Standard Specification for Carbon Structural Steel
• ASTM A53 Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
• ASTM A90 Standard Specification for Weight [Mass] of Coating on Iron and Steel Articles with Zinc of Zinc-Alloy Coatings
• ASTM A105 Standard Specification for Forgings, Carbon Steel for Piping Components
• ASTM A106 Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service
• ASTM A108 Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished
• ASTM A123 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
• ASTM A126 Standard specification for three classes of gray iron for castings intended for use as valve pressure retaining parts, pipe fittings, and flanges.
• ASTM A148 Standard Specification for Steel Castings, High Strength, for Structural Purposes
• ASTM A153 Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
• ASTM A193/A193M Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
• ASTM A194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-Temperature Service, or Both
• ASTM A228 Standard Specification for Steel Wire, Music Spring Quality
• ASTM A240 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
• ASTM A249/A249M Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
• ASTM A255 Standard Test Methods for Determining Hardenability of Steel (Includes JOMINY test)
• ASTM A270 Standard Specification for Seamless and Welded Austenitic and Ferritic/Austenitic Stainless Steel Sanitary Tubing
• ASTM A297 Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application
• ASTM A304 Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements
• ASTM A307 Standard Specification for carbon steel bolts and studs ranging from 1/4" through 4" diameter.
• ASTM A320/A320M Specification for Alloy/Steel Bolting Materials for Low-Temperature Service
• ASTM A325 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• ASTM A325M Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength
• ASTM A350 Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components
• ASTM A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners
• ASTM A370 Standard Testing Methods and Definitions for Mechanical Testing of Steel Products
• ASTM A380 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
• ASTM A385 Standard Practice for Providing High-Quality Zinc Coatings (Hot Dip)
• ASTM A490 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
• ASTM A490M Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints
• ASTM A500 Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes
• ASTM A513 Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
• ASTM A514 Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for Welding
• ASTM A516 Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate and Lower Temperature Service
• ASTM A517 Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered
• ASTM A519 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing
• ASTM A529 Standard Specification for High-Strength Carbon-Maganese Steel of Structural Quality
• ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts
• ASTM A564 Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
• ASTM A568 Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
• ASTM A588 Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance
• ASTM A615/615M Standard Specification for Deformed and Plain Carbon- Steel Bars for Concrete
• ASTM A653 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
• ASTM A706 Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
• ASTM A743 Standard Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application
• ASTM A759 Standard Specification for Carbon Steel Crane Rails
• ASTM A780 Standard Specification for Repair of Damaged and Uncated Areas of Hot-Dip Galvanized Coatings
• ASTM A786 Standard Specification for Hot-Rolled Carbon, Low-Alloy, High-Strength Low-Alloy, and Alloy Steel Floor Plates
• ASTM A820 Standard Specification for Steel Fibers for Fiber-Reinforced Concrete
• ASTM A962/A962M Specification for Common Requirements for Steel Fasteners or Fastener Materials, or Both, Intended for Use at Any Temperature from Cryogenic to the Creep Range
• ASTM A992 Standard Specification for Structural Steel Shapes
• ASTM A994 Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
• ASTM A1008 Standard Specification for Structural Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
• ASTM A1011 Standard Specification for Structural Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
• ASTM A1018 Standard Specification for Structural Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

B

• B1-01 Standard Specification for Hard-Drawn Copper Wire
• B2-08 Standard Specification for Medium-Hard-Drawn Copper Wire
• B3-01(2007) Standard Specification for Soft or Annealed Copper Wire
• B5-00(2005) Standard Specification for High Conductivity Tough-Pitch Copper Refinery Shapes
• B6-08 Standard Specification for Zinc
• B8-04 Standard Specification for Concentric-Lay-Stranded Copper Conductors, Hard, Medium-Hard, or Soft
• B9-90(2008) Standard Specification for Bronze Trolley Wire
• B16/B16M-05 Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
• B19-05 Standard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks
• B21/B21M-06 Standard Specification for Naval Brass Rod, Bar, and Shapes
• B22-08 Standard Specification for Bronze Castings for Bridges and Turntables
• B23-00(2005) Standard Specification for White Metal Bearing Alloys (Known Commercially as "Babbitt Metal")
• B26/B26M-05 Standard Specification for Aluminum-Alloy Sand Castings
• B29-03 Standard Specification for Refined Lead
• B30-09 Standard Specification for Copper Alloys in Ingot Form
• B30-08a Standard Specification for Copper Alloys in Ingot Form CHINESE TRANSLATION
• B32-08 Standard Specification for Solder Metal
• B33-04 Standard Specification for Tinned Soft or Annealed Copper Wire for Electrical Purposes
• B36/B36M-08a Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar
• B37-08 Standard Specification for Aluminum for Use in Iron and Steel Manufacture
• B39-79(2008) Standard Specification for Nickel
• B42-02e1 Standard Specification for Seamless Copper Pipe, Standard Sizes
• B43-98(2004) Standard Specification for Seamless Red Brass Pipe, Standard Sizes
• B47-95a(2007) Standard Specification for Copper Trolley Wire
• B48-00(2005)e1 Standard Specification for Soft Rectangular and Square Bare Copper Wire for Electrical Conductors
• B49-08a Standard Specification for Copper Rod Drawing Stock for Electrical Purposes
• B61-08 Standard Specification for Steam or Valve Bronze Castings
• B62-09 Standard Specification for Composition Bronze or Ounce Metal Castings
• B63-07 Standard Test Method for Resistivity of Metallically Conducting Resistance and Contact Materials
• B66/B66M-06e1 Standard Specification for Bronze Castings for Steam Locomotive Wearing Parts
• B67-05 Standard Specification for Car and Tender Journal Bearings, Lined
• B68-02 Standard Specification for Seamless Copper Tube, Bright Annealed
• B68M-99(2005) Standard Specification for Seamless Copper Tube, Bright Annealed [Metric]
• B69-08 Standard Specification for Rolled Zinc
• B70-90(2007) Standard Test Method for Change of Resistance With Temperature of Metallic Materials for Electrical Heating
• B75-02 Standard Specification for Seamless Copper Tube
• B75M-99(2005) Standard Specification for Seamless Copper Tube [Metric]
• B76-90(2007) Standard Test Method for Accelerated Life of Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating
• B77-07 Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys
• B78-90(2007) Standard Test Method of Accelerated Life of Iron-Chromium-Aluminum Alloys for Electrical Heating
• B80-07 Standard Specification for Magnesium-Alloy Sand Castings
• B84-07 Standard Test Method for Temperature-Resistance Constants of Alloy Wires for Precision Resistors
• B85/B85M-08 Standard Specification for Aluminum-Alloy Die Castings
• B86-08 Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings
• B88-03 Standard Specification for Seamless Copper Water Tube
• B88M-05 Standard Specification for Seamless Copper Water Tube [Metric]
• B90/B90M-07 Standard Specification for Magnesium-Alloy Sheet and Plate
• B91-07 Standard Specification for Magnesium-Alloy Forgings
• B92/B92M-07 Standard Specification for Unalloyed Magnesium Ingot and Stick For Remelting
• B93/B93M-07 Standard Specification for Magnesium Alloys in Ingot Form for Sand Castings, Permanent Mold Castings, and Die Castings
• B94-07 Standard Specification for Magnesium-Alloy Die Castings
• B96/B96M-06 Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels
• B98/B98M-08 Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes
• B99/B99M-06 Standard Specification for Copper-Silicon Alloy Wire for General Applications
• B100-08 Standard Specification for Wrought Copper-Alloy Bearing and Expansion Plates and Sheets for Bridge and Other Structural Use
• B101-07 Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction
• B102-00(2005) Standard Specification for Lead- and Tin-Alloy Die Castings
• B103/B103M-09 Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar
• B105-05 Standard Specification for Hard-Drawn Copper Alloy Wires for Electric Conductors
• B106-08 Standard Test Methods for Flexivity of Thermostat Metals
• B107/B107M-07 Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire
• B108/B108M-08 Standard Specification for Aluminum-Alloy Permanent Mold Castings
• B111/B111M-09 Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
• B114-07 Standard Test Method for Temperature-Resistance Constants of Sheet Materials for Shunts and Precision Resistors
• B115-00(2004) Standard Specification for Electrolytic Copper Cathode
• B116-95(2007) Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage
• B117 Standard Practice for Operating Salt Spray (Fog) Apparatus
• B121/B121M-01(2006) Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar
• B122/B122M-08 Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar
• B124/B124M-08a Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
• B127-05 Standard Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
• B129-07 Standard Specification for Cartridge Brass Cartridge Case Cups
• B130-08 Standard Specification for Commercial Bronze Strip for Bullet Jackets
• B131-07 Standard Specification for Copper Alloy Bullet Jacket Cups
• B134/B134M-08 Standard Specification for Brass Wire
• B135-08a Standard Specification for Seamless Brass Tube
• B135M-08a Standard Specification for Seamless Brass Tube [Metric]
• B136-84(2008)e1 Standard Method for Measurement of Stain Resistance of Anodic Coatings on Aluminum
• B137-95(2004) Standard Test Method for Measurement of Coating Mass Per Unit Area on Anodically Coated Aluminum
• B138/B138M-06 Standard Specification for Manganese Bronze Rod, Bar, and Shapes
• B139/B139M-07 Standard Specification for Phosphor Bronze Rod, Bar, and Shapes
• B140/B140M-07 Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
• B148-97(2003)e1 Standard Specification for Aluminum-Bronze Sand Castings
• B150/B150M-08 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
• B151/B151M-05 Standard Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar
• B152/B152M-06ae1 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• B153-05 Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
• B154-05 Standard Test Method for Mercurous Nitrate Test for Copper Alloys
• B159/B159M-05 Standard Specification for Phosphor Bronze Wire
• B160-05e1 Standard Specification for Nickel Rod and Bar
• B161-05e1 Standard Specification for Nickel Seamless Pipe and Tube
• B162-99(2005)e1 Standard Specification for Nickel Plate, Sheet, and Strip
• B163-08 Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
• B164-03(2008) Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire
• B165-05 Standard Specification for Nickel-Copper Alloy (UNS N04400)* Seamless Pipe and Tube
• B166-08 Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696)* and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Rod, Bar, and Wire
• B167-08 Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696)* and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Seamless Pipe and Tube
• B168-08 Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696) and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Plate, Sheet, and Strip
• B169/B169M-05 Standard Specification for Aluminum Bronze Sheet, Strip, and Rolled Bar
• B170-99(2004) Standard Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes
• B171/B171M-09 Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers
• B172-01a(2007)e1 Standard Specification for Rope-Lay-Stranded Copper Conductors Having Bunch-Stranded Members, for Electrical Conductors
• B173-01a(2007)e1 Standard Specification for Rope-Lay-Stranded Copper Conductors Having Concentric-Stranded Members, for Electrical Conductors
• B174-02(2007)e1 Standard Specification for Bunch-Stranded Copper Conductors for Electrical Conductors
• B176-08 Standard Specification for Copper-Alloy Die Castings
• B177-01(2006)e1 Standard Guide for Engineering Chromium Electroplating
• B179-06 Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
• B183-79(2004)e1 Standard Practice for Preparation of Low-Carbon Steel for Electroplating
• B187/B187M-06 Standard Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
• B188-02 Standard Specification for Seamless Copper Bus Pipe and Tube
• B189-05 Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes
• B193-02(2008) Standard Test Method for Resistivity of Electrical Conductor Materials
• B194-08 Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
• B196/B196M-07 Standard Specification for Copper-Beryllium Alloy Rod and Bar
• B197/B197M-07 Standard Specification for Copper-Beryllium Alloy Wire
• B199-07 Standard Specification for Magnesium-Alloy Permanent Mold Castings
• B200-85(2004) Standard Specification for Electrodeposited Coatings of Lead and Lead-Tin Alloys on Steel and Ferrous Alloys
• B201-80(2004) Standard Practice for Testing Chromate Coatings on Zinc and Cadmium Surfaces
• B206/B206M-07 Standard Specification for Copper-Nickel-Zinc (Nickel Silver) Wire and Copper-Nickel Alloy Wire
• B208-06 Standard Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous Castings
• B208-06 Standard Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous Castings CHINESE TRANSLATION
• B209-07 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
• B209M-07 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]
• B210-04 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
• B210M-05 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes [Metric]
• B211-03 Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
• B211M-03 Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire [Metric]
• B212-99(2006) Standard Test Method for Apparent Density of Free-Flowing Metal Powders Using the Hall Flowmeter Funnel
• B213-03 Standard Test Method for Flow Rate of Metal Powders
• B214-07 Standard Test Method for Sieve Analysis of Metal Powders
• B215-08 Standard Practices for Sampling Metal Powders
• B216-97(2003) Standard Specification for Tough-Pitch Fire-Refined Copper—Refinery Shapes
• B221M-07 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes [Metric]
• B221-08 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
• B223-08 Standard Test Method for Modulus of Elasticity of Thermostat Metals (Cantilever Beam Method)
• B224-04 Standard Classification of Coppers
• B226-04 Standard Specification for Cored, Annular, Concentric-Lay-Stranded Copper Conductors
• B227-04 Standard Specification for Hard-Drawn Copper-Clad Steel Wire
• B228-04 Standard Specification for Concentric-Lay-Stranded Copper-Clad Steel Conductors
• B229-04 Standard Specification for Concentric-Lay-Stranded Copper and Copper-Clad Steel Composite Conductors
• B230/B230M-07 Standard Specification for Aluminum 1350-H19 Wire for Electrical Purposes
• B231/B231M-04 Standard Specification for Concentric-Lay-Stranded Aluminum 1350 Conductors
• B232/B232M-01e1 Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Reinforced (ACSR)
• B233-97(2007) Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes
• B234-04 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers
• B234M-04 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers [Metric]
• B236M-07 Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) [Metric]
• B236-07 Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars)
• B237-01(2006) Standard Specification for Refined Antimony
• B240-07e1 Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings
• B241/B241M-02 Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
• B242-99(2004)e1 Standard Guide for Preparation of High-Carbon Steel for Electroplating
• B243-09 Standard Terminology of Powder Metallurgy
• B244-09 Standard Test Method for Measurement of Thickness of Anodic Coatings on Aluminum and of Other Nonconductive Coatings on Nonmagnetic Basis Metals with Eddy-Current Instruments
• B246-05 Standard Specification for Tinned Hard-Drawn and Medium-Hard-Drawn Copper Wire for Electrical Purposes
• B247-02a Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings
• B247M-02a Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings [Metric]
• B248-07 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
• B248M-07 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar [Metric]
• B249/B249M-06 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
• B250/B250M-07 Standard Specification for General Requirements for Wrought Copper Alloy Wire
• B251M-97(2003) Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube [Metric]
• B251-02e1 Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube
• B252-92(2004) Standard Guide for Preparation of Zinc Alloy Die Castings for Electroplating and Conversion Coatings
• B253-87(2005)e1 Standard Guide for Preparation of Aluminum Alloys for Electroplating
• B254-92(2004)e1 Standard Practice for Preparation of and Electroplating on Stainless Steel
• B258-02(2008) Standard Specification for Standard Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires Used as Electrical Conductors
• B263-04 Standard Test Method for Determination of Cross-Sectional Area of Stranded Conductors
• B265-09a Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate
• B267-07 Standard Specification for Wire for Use In Wire-Wound Resistors
• B271-08 Standard Specification for Copper-Base Alloy Centrifugal Castings
• B272-07 Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)
• B275-05 Standard Practice for Codification of Certain Nonferrous Metals and Alloys, Cast and Wrought
• B276-05e1 Standard Test Method for Apparent Porosity in Cemented Carbides
• B277-95(2006) Standard Test Method for Hardness of Electrical Contact Materials
• B279-04 Standard Test Method for Stiffness of Bare Soft Square and Rectangular Copper and Aluminum Wire for Magnet Wire Fabrication
• B280-08 Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
• B281-88(2008) Standard Practice for Preparation of Copper and Copper-Base Alloys for Electroplating and Conversion Coatings
• B283-09 Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
• B286-07 Standard Specification for Copper Conductors for Use in Hookup Wire for Electronic Equipment
• B294-92(2006) Standard Test Method for Hardness Testing of Cemented Carbides
• B296-03(2008) Standard Practice for Temper Designations of Magnesium Alloys, Cast and Wrought
• B298-07 Standard Specification for Silver-Coated Soft or Annealed Copper Wire
• B299-08 Standard Specification for Titanium Sponge
• B301/B301M-08 Standard Specification for Free-Cutting Copper Rod, Bar, Wire, and Shapes
• B302-07 Standard Specification for Threadless Copper Pipe, Standard Sizes
• B306-09 Standard Specification for Copper Drainage Tube (DWV)
• B308/B308M-02 Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles
• B311-08 Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity
• B312-96(2002) Standard Test Method for Green Strength for Compacted Metal Powder Specimens
• B313/B313M-02e1 Standard Specification for Aluminum and Aluminum-Alloy Round Welded Tubes
• B315-06 Standard Specification for Seamless Copper Alloy Pipe and Tube
• B316/B316M-02 Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
• B317/B317M-07 Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
• B319-91(2004) Standard Guide for Preparation of Lead and Lead Alloys for Electroplating
• B320-60(2008) Standard Practice for Preparation of Iron Castings for Electroplating
• B322-99(2004) Standard Guide for Cleaning Metals Prior to Electroplating
• B324-01(2007) Standard Specification for Aluminum Rectangular and Square Wire for Electrical Purposes
• B327-09 Standard Specification for Master Alloys Used in Making Zinc Die Casting Alloys
• B328-96(2003)e1 Standard Test Method for Density, Oil Content, and Interconnected Porosity of Sintered Metal Structural Parts and Oil-Impregnated Bearings
• B329-06 Standard Test Method for Apparent Density of Metal Powders and Compounds Using the Scott Volumeter
• B330-07 Standard Test Method for Fisher Number of Metal Powders and Related Compounds
• B331-95(2002) Standard Test Method for Compressibility of Metal Powders in Uniaxial Compaction
• B333-03(2008) Standard Specification for Nickel-Molybdenum Alloy Plate, Sheet, and Strip
• B335-03(2008) Standard Specification for Nickel-Molybdenum Alloy Rod
• B338-09 Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers
• B339-00(2005) Standard Specification for Pig Tin
• B343-92a(2004)e1 Standard Practice for Preparation of Nickel for Electroplating with Nickel
• B344-01 Standard Specification for Drawn or Rolled Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating Elements
• B345/B345M-02 Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube for Gas and Oil Transmission and Distribution Piping Systems
• B348-09 Standard Specification for Titanium and Titanium Alloy Bars and Billets
• B349/B349M-09 Standard Specification for Zirconium Sponge and Other Forms of Virgin Metal for Nuclear Application
• B350/B350M-02(2006) Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application
• B351/B351M-08e1 Standard Specification for Hot-Rolled and Cold-Finished Zirconium and Zirconium Alloy Bars, Rod, and Wire for Nuclear Application
• B352/B352M-02(2006) Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application
• B353-07 Standard Specification for Wrought Zirconium and Zirconium Alloy Seamless and Welded Tubes for Nuclear Service (Except Nuclear Fuel Cladding)
• B354-05 Standard Terminology Relating to Uninsulated Metallic Electrical Conductors
• B355-06 Standard Specification for Nickel-Coated Soft or Annealed Copper Wire
• B359/B359M-02(2006) Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins
• B360-01 Standard Specification for Hard-Drawn Copper Capillary Tube for Restrictor Applications
• B361-08 Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings
• B362-91(2008) Standard Test Method for Mechanical Torque Rate of Spiral Coils of Thermostat Metal
• B363-06a Standard Specification for Seamless and Welded Unalloyed Titanium and Titanium Alloy Welding Fittings
• B364-96(2009) Standard Specification for Tantalum and Tantalum Alloy Ingots
• B365-98(2004) Standard Specification for Tantalum and Tantalum Alloy Rod and Wire
• B366-04be1 Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• B367-09 Standard Specification for Titanium and Titanium Alloy Castings
• B368-09 Standard Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)
• B369-09 Standard Specification for Copper-Nickel Alloy Castings
• B370-09 Standard Specification for Copper Sheet and Strip for Building Construction
• B371/B371M-08 Standard Specification for Copper-Zinc-Silicon Alloy Rod
• B372-97(2003) Standard Specification for Seamless Copper and Copper-Alloy Rectangular Waveguide Tube
• B373-00(2006) Standard Specification for Aluminum Foil for Capacitors
• B374-06 Standard Terminology Relating to Electroplating
• B379-04 Standard Specification for Phosphorized Coppers—Refinery Shapes
• B380-97(2008)e1 Standard Test Method for Corrosion Testing of Decorative Electrodeposited Coatings by the Corrodkote Procedure
• B381-09 Standard Specification for Titanium and Titanium Alloy Forgings
• B386-03 Standard Specification for Molybdenum and Molybdenum Alloy Plate, Sheet, Strip, and Foil
• B387-90(2001) Standard Specification for Molybdenum and Molybdenum Alloy Bar, Rod, and Wire
• B388-06 Standard Specification for Thermostat Metal Sheet and Strip
• B389-81(2008) Standard Test Method for Thermal Deflection Rate of Spiral and Helical Coils of Thermostat Metal
• B390-92(2006) Standard Practice for Evaluating Apparent Grain Size and Distribution of Cemented Tungsten Carbides
• B391-03 Standard Specification for Niobium and Niobium Alloy Ingots
• B392-03 Standard Specification for Niobium and Niobium Alloy Bar, Rod, and Wire
• B393-05 Standard Specification for Niobium and Niobium Alloy Strip, Sheet, and Plate
• B394-03 Standard Specification for Niobium and Niobium Alloy Seamless and Welded Tubes
• B395/B395M-08 Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes
• B398/B398M-02(2007) Standard Specification for Aluminum-Alloy 6201-T81 Wire for Electrical Purposes
• B399/B399M-04 Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy 6201-T81 Conductors
• B400-08 Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum 1350 Conductors
• B401-04 Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/COMP)
• B403-07 Standard Specification for Magnesium-Alloy Investment Castings
• B406-96(2005) Standard Test Method for Transverse Rupture Strength of Cemented Carbides
• B407-08a Standard Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube
• B408-06 Standard Specification for Nickel-Iron-Chromium Alloy Rod and Bar
• B409-06e1 Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip
• B411/B411M-08 Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar
• B413-97a(2008) Standard Specification for Refined Silver
• B415-98(2007) Standard Specification for Hard-Drawn Aluminum-Clad Steel Wire
• B416-98(2007) Standard Specification for Concentric-Lay-Stranded Aluminum-Clad Steel Conductors
• B417-00(2006)e1 Standard Test Method for Apparent Density of Non-Free-Flowing Metal Powders Using the Carney Funnel
• B418-08 Standard Specification for Cast and Wrought Galvanic Zinc Anodes
• B422-08a Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip
• B423-05 Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 and N08221)* Seamless Pipe and Tube
• B424-05 Standard Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825 and UNS N08221)* Plate, Sheet, and Strip
• B425-99(2005) Standard Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825 and UNS N08221) Rod and Bar
• B427-02 Standard Specification for Gear Bronze Alloy Castings
• B428-09 Standard Test Method for Angle of Twist in Rectangular and Square Copper and Copper Alloy Tube
• B429/B429M-06 Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube
• B430-97(2006)e1 Standard Test Method for Particle Size Distribution of Refractory Metal Powders and Related Compounds by Turbidimetry
• B432-09 Standard Specification for Copper and Copper Alloy Clad Steel Plate
• B434-06 Standard Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, UNS N10242)* Plate, Sheet, and Strip
• B435-06 Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
• B438-08 Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated)
• B439-08 Standard Specification for Iron-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated)
• B440-00(2005) Standard Specification for Cadmium
• B441-04 Standard Specification for Copper-Cobalt-Beryllium, Copper-Nickel-Beryllium, and Copper-Nickel-Lead-Beryllium Rod and Bar (UNS Nos. C17500, C17510, and C17465)
• B443-00(2005) Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) and Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219)* Plate, Sheet, and Strip
• B444-06 Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloys (UNS N06625 and UNS N06852) and Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219) Pipe and Tube
• B446-03(2008) Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650)* Rod and Bar
• B447-07 Standard Specification for Welded Copper Tube
• B449-93(2004) Standard Specification for Chromates on Aluminum
• B452-02 Standard Specification for Copper-Clad Steel Wire for Electronic Application
• B453/B453M-08 Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes
• B455-05 Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Extruded Shapes
• B456-03 Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chromium
• B457-67(2008)e1 Standard Test Method for Measurement of Impedance of Anodic Coatings on Aluminum
• B462-06 Specification for Forged or Rolled UNS N06030,N06022,N06035,N06200,N06059,N06686,N08020,N08024,N08026,N08367,N10276,N10665, N10675,N10629, N08031,N06045, N06025, & R20033 Alloy Pipe Flanges, Forged Fitting, & Values & Parts for Corrosive
• B463-04 Standard Specification for UNS N08020, UNS N08026, and UNS N08024 Alloy Plate, Sheet, and Strip
• B464-05 Standard Specification for Welded UNS N08020, N08024, and N08026 Alloy Pipe
• B465-04 Standard Specification for Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
• B466/B466M-07 Standard Specification for Seamless Copper-Nickel Pipe and Tube
• B467-88(2003) Standard Specification for Welded Copper-Nickel Pipe
• B468-04 Standard Specification for Welded UNS N08020, N08024, and N08026 Alloy Tubes
• B470-02(2007) Standard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic Equipment
• B472-04a Standard Specification for Nickel Alloy Billets and Bars for Reforging
• B473-07 Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire
• B474-03 Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe
• B475-07 Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Round Weaving Wire
• B476-01(2006) Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials
• B477-97(2008) Standard Specification for Gold-Silver-Nickel Electrical Contact Alloy
• B478-85(2008) Standard Test Method for Cross Curvature of Thermostat Metals
• B479-06 Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications
• B480-88(2006) Standard Guide for Preparation of Magnesium and Magnesium Alloys for Electroplating
• B481-68(2008) Standard Practice for Preparation of Titanium and Titanium Alloys

for Electroplating

• B482-85(2008) Standard Practice for

Preparation of Tungsten and Tungsten Alloys for Electroplating

• B483/B483M-03 Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Pipe for General Purpose Applications
• B487-85(2007) Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of a Cross Section
• B488-01(2006) Standard Specification for Electrodeposited Coatings of Gold for Engineering Uses
• B489-85(2008)e1 Standard Practice for Bend Test for Ductility of Electrodeposited and Autocatalytically Deposited Metal Coatings on Metals
• B490-09 Standard Practice for Micrometer Bend Test for Ductility of Electrodeposits
• B491/B491M-06 Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications
• B493/B493M-08 Standard Specification for Zirconium and Zirconium Alloy Forgings
• B494/B494M-08 Standard Specification for Primary Zirconium
• B495-05 Standard Specification for Zirconium and Zirconium Alloy Ingots
• B496-04 Standard Specification for Compact Round Concentric-Lay-Stranded Copper Conductors
• B497-00(2006) Standard Guide for Measuring Voltage Drop on Closed Arcing Contacts
• B498/B498M-08 Standard Specification for Zinc-Coated (Galvanized) Steel Core Wire for Use in Overhead Electrical Conductors
• B499-09 Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals
• B500/B500M-09 Standard Specification for Metallic Coated Stranded Steel Core for Use in Overhead Electrical Conductors
• B501-04 Standard Specification for Silver-Coated, Copper-Clad Steel Wire for Electronic Application
• B502-02(2007) Standard Specification for Aluminum-Clad Steel Core Wire for Aluminum Conductors, Aluminum-Clad Steel Reinforced
• B504-90(2007) Standard Test Method for Measurement of Thickness of Metallic Coatings by the Coulometric Method
• B505/B505M-08a Standard Specification for Copper Alloy Continuous Castings
• B506-09 Specification for Copper-Clad Stainless Steel Sheet and Strip for Building Construction
• B507-86(2008)e1 Standard Practice for Design of Articles to Be Electroplated on Racks
• B508-08 Standard Specification for Copper Alloy Strip for Flexible Metal Hose
• B511-01(2005) Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Bars and Shapes
• B512-04 Standard Specification for Nickel-Chromium-Silicon Alloy (UNS N08330) Billets and Bars
• B514-05 Standard Specification for Welded Nickel-Iron-Chromium Alloy Pipe
• B515-95(2002) Standard Specification for Welded UNS N08120, UNS N08800, UNS N08810, and UNS N08811 Alloy Tubes
• B516-03(2009) Standard Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045 Tubes
• B517-05 Standard Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045) Pipe
• B520-93(2007) Standard Specification for Tin-Coated, Copper-Clad Steel Wire for Electronic Application
• B521-98(2004) Standard Specification for Tantalum and Tantalum Alloy Seamless and Welded Tubes
• B522-01(2006) Standard Specification for Gold-Silver-Platinum Electrical Contact Alloy
• B523/B523M-07 Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes
• B524/B524M-99(2005) Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum-Alloy Reinforced (ACAR, 1350/6201)
• B527-06 Standard Test Method for Determination of Tap Density of Metallic Powders and Compounds
• B528-05 Standard Test Method for Transverse Rupture Strength of Metal Powder Specimens
• B530-02 Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Electrodeposited Nickel Coatings on Magnetic and Nonmagnetic Substrates
• B532-85(2007) Standard Specification for Appearance of Electroplated Plastic Surfaces
• B533-85(2004) Standard Test Method for Peel Strength of Metal Electroplated Plastics
• B534-07 Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
• B535-06 Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube
• B536-07 Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Plate, Sheet, and Strip
• B537-70(2007) Standard Practice for Rating of Electroplated Panels Subjected to Atmospheric Exposure
• B539-02(2008) Standard Test Methods for Measuring Resistance of Electrical Connections (Static Contacts)
• B540-97(2008) Standard Specification for Palladium Electrical Contact Alloy
• B541-01(2006) Standard Specification for Gold Electrical Contact Alloy
• B542-07 Standard Terminology Relating to Electrical Contacts and Their Use
• B543-07e1 Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube
• B545-97(2004)e1 Standard Specification for Electrodeposited Coatings of Tin
• B546-04 Standard Specification for Electric Fusion-Welded Ni-Cr-Co-Mo Alloy (UNS N06617), Ni-Fe-Cr-Si Alloys (UNS N08330 and UNS N08332), Ni-Cr-Fe-Al Alloy (UNS N06603), Ni-Cr-Fe Alloy (UNS N06025), and Ni-Cr-Fe-Si Alloy (UNS N06045) Pipe
• B547/B547M-02 Standard Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round Tube
• B548-03 Standard Test Method for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels
• B549-04 Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Aluminum-Clad Steel Reinforced (ACSR/AW)
• B550/B550M-07 Standard Specification for Zirconium and Zirconium Alloy Bar and Wire
• B551/B551M-07 Standard Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate
• B552-08 Standard Specification for Seamless and Welded Copper–Nickel Tubes for Water Desalting Plants
• B555-86(2007) Standard Guide for Measurement of Electrodeposited Metallic Coating Thicknesses by Dropping Test
• B556-90(2007) Standard Guide for Measurement of Thin Chromium Coatings by Spot Test
• B557-06 Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
• B557M-07e1 Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric]
• B558-79(2008) Standard Practice for Preparation of Nickel Alloys for Electroplating
• B559-93(2007) Standard Specification for Nickel-Coated, Copper-Clad Steel Wire for Electronic Application
• B560-00(2005) Standard Specification for Modern Pewter Alloys
• B561-94(2005) Standard Specification for Refined Platinum
• B562-95(2005) Standard Specification for Refined Gold
• B563-01(2006) Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy
• B564-06a Standard Specification for Nickel Alloy Forgings
• B565-04 Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods
• B566-04a Standard Specification for Copper-Clad Aluminum Wire
• B567-98(2003) Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method
• B568-98(2004) Standard Test Method for Measurement of Coating Thickness by X-Ray Spectrometry
• B569-09 Standard Specification for Brass Strip in Narrow Widths and Light Gage for Heat-Exchanger Tubing
• B570-06 Standard Specification for Copper-Beryllium Alloy (UNS Nos. C17000 and C17200) Forgings and Extrusions
• B571-97(2008)e1 Standard Practice for Qualitative Adhesion Testing of Metallic Coatings
• B572-06 Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod
• B573-06 Standard Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, N10242)* Rod
• B574-06e1 Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod
• B575-06 Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Plate, Sheet, and Strip
• B576-94(2005) Standard Guide for Arc Erosion Testing of Electrical Contact Materials
• B577-93(2004)e1 Standard Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in Copper
• B578-87(2004) Standard Test Method for Microhardness of Electroplated Coatings
• B579-73(2004) Standard Specification for Electrodeposited Coatings of Tin-Lead Alloy (Solder Plate)
• B580-79(2004) Standard Specification for Anodic Oxide Coatings on Aluminum
• B581-02(2008) Standard Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod
• B582-07 Standard Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and Strip
• B584-08a Standard Specification for Copper Alloy Sand Castings for General Applications
• B584-08a Standard Specification for Copper Alloy Sand Castings for General Applications CHINESE TRANSLATION
• B587-08 Standard Specification for Welded Brass Tube
• B588-88(2006) Standard Test Method for Measurement of Thickness of Transparent or Opaque Coatings by Double-Beam Interference Microscope Technique
• B589-94(2005) Standard Specification for Refined Palladium
• B591-09 Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate, Sheet, Strip, and Rolled Bar
• B592-01(2006) Standard Specification for Copper-Zinc-aluminum-Cobalt Alloy, Copper-Zinc-Tin-Iron Alloy Plate, Sheet, Strip, and Rolled Bar
• B593-96(2003)e1 Standard Test Method for Bending Fatigue Testing for Copper-Alloy Spring Materials
• B594-06 Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace Applications
• B595-95(2006) Standard Specification for Sintered Aluminum Structural Parts
• B596-89(2006) Standard Specification for Gold-Copper Alloy Electrical Contact Material
• B598-09 Standard Practice for Determining Offset Yield Strength in Tension for Copper Alloys
• B599-92(2009)e1 Standard Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Plate, Sheet, and Strip
• B600-91(2002)e1 Standard Guide for Descaling and Cleaning Titanium and Titanium Alloy Surfaces
• B601-07 Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast
• B602-88(2005) Standard Test Method for Attribute Sampling of Metallic and Inorganic Coatings
• B603-07 Standard Specification for Drawn or Rolled Iron-Chromium-Aluminum Alloys for Electrical Heating Elements
• B604-91(2008) Standard Specification for Decorative Electroplated Coatings of Copper Plus Nickel Plus Chromium on Plastics
• B605-95a(2004) Standard Specification for Electrodeposited Coatings of Tin-Nickel Alloy
• B606-08 Standard Specification for High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Aluminum and Aluminum-Alloy Conductors, Steel Reinforced
• B607-91(2008) Standard Specification for Autocatalytic Nickel Boron Coatings for Engineering Use
• B608-07 Standard Specification for Welded Copper-Alloy Pipe
• B609/B609M-99(2004) Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes
• B610-08 Standard Test Method for Measuring Dimensional Changes Associated with Processing Metal Powders
• B611-85(2005) Standard Test Method for Abrasive Wear Resistance of Cemented Carbides
• B613-76(2006) Standard Guide for Preparing Specifications for Miniature Brushes of Composite Materials for Sliding Electric Contacts
• B614-05 Standard Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces
• B615-79(2006) Standard Practice for Measuring Electrical Contact Noise in Sliding Electrical Contacts
• B616-96(2006) Standard Specification for Refined Rhodium
• B617-98(2004) Standard Specification for Coin Silver Electrical Contact Alloy
• B618/B618M-08 Standard Specification for Aluminum-Alloy Investment Castings
• B619-06 Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
• B620-03(2008) Standard Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Plate, Sheet, and Strip
• B621-02(2006) Standard Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Rod
• B622-06 Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
• B624-07 Standard Specification for High-Strength, High-Conductivity Copper-Alloy Wire for Electronic Application
• B625-05 Standard Specification for UNS N08925, UNS N08031, UNS N08932, UNS N08926, UNS N08354, and UNS R20033 Plate, Sheet, and Strip
• B626-06 Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Tube
• B628-98(2004) Standard Specification for Silver-Copper Eutectic Electrical Contact Alloy
• B629-77(2008) Standard Practice for Preparation of Molybdenum and Molybdenum Alloys for Electroplating
• B630-88(2006) Standard Practice for Preparation of Chromium for Electroplating with Chromium
• B631-93(2004) Standard Specification for Silver-Tungsten Electrical Contact Materials
• B632/B632M-08 Standard Specification for Aluminum-Alloy Rolled Tread Plate
• B633-07 Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
• B634-88(2004)e1 Standard Specification for Electrodeposited Coatings of Rhodium for Engineering Use
• B635-00(2004)e1 Standard Specification for Coatings of Cadmium-Tin Mechanically Deposited
• B636-84(2006)e1 Standard Test Method for Measurement of Internal Stress of Plated Metallic Coatings with the Spiral Contractometer
• B637-06e1 Standard Specification for Precipitation-Hardening Nickel Alloy Bars, Forgings, and Forging Stock for High-Temperature Service
• B639-02(2008) Standard Specification for Precipitation Hardening Cobalt-Containing Alloys (UNS R30155 and UNS R30816) Rod, Bar, Forgings, and Forging Stock for High-Temperature Service
• B640-07 Standard Specification for Welded Copper Tube for Air Conditioning and Refrigeration Service
• B643-00(2005) Standard Specification for Copper-Beryllium Alloy Seamless Tube
• B644-05 Standard Specification for Copper Alloy Addition Agents
• B645-07 Standard Practice for Linear-Elastic Plane-Strain Fracture Toughness Testing of Aluminum Alloys
• B646-06a Standard Practice for Fracture Toughness Testing of Aluminum Alloys
• B647-84(2006) Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage
• B648-78(2006) Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Barcol Impressor
• B649-06 Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), and Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire, and Ni-Cr-Fe-Mo-N Alloy (UNS N08936) Wire
• B650-95(2008) Standard Specification for Electrodeposited Engineering Chromium Coatings on Ferrous Substrates
• B651-83(2006) Standard Test Method for Measurement of Corrosion Sites in Nickel Plus Chromium or Copper Plus Nickel Plus Chromium Electroplated Surfaces with Double-Beam Interference Microscope
• B652/B652M-04 Standard Specification for Niobium-Hafnium Alloy Ingots
• B653/B653M-06 Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings
• B654/B654M-04 Standard Specification for Niobium-Hafnium Alloy Foil, Sheet, Strip, and Plate
• B655/B655M-04 Standard Specification for Niobium-Hafnium Alloy Bar, Rod, and Wire
• B657-05 Guide for Metallographic Identification of Microstructure in Cemented Carbides
• B658/B658M-06 Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe
• B659-90(2008)e1 Standard Guide for Measuring Thickness of Metallic and Inorganic Coatings
• B660-08 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
• B661-06 Standard Practice for Heat Treatment of Magnesium Alloys
• B662-94(2006) Standard Specification for Silver-Molybdenum Electrical Contact Material
• B663-94(2006) Standard Specification for Silver-Tungsten Carbide Electrical Contact Material
• B664-90(2006) Standard Specification for 80% Silver-20 % Graphite Sliding Contact Material
• B665-08 Standard Guide for Metallographic Sample Preparation of Cemented Tungsten Carbides
• B666/B666M-08 Standard Practice for Identification Marking of Aluminum and Magnesium Products
• B667-97(2009) Standard Practice for Construction and Use of a Probe for Measuring Electrical Contact Resistance
• B668-05 Standard Specification for UNS N08028 Seamless Pipe and Tube
• B670-07 Standard Specification for Precipitation-Hardening Nickel Alloy (UNS N07718) Plate, Sheet, and Strip for High-Temperature Service
• B671-81(2005) Standard Specification for Refined Iridium
• B672-02(2007) Standard Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Bar and Wire
• B673-05e1 Standard Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Pipe
• B674-05 Standard Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Tube
• B675-02(2007) Standard Specification for UNS N08367 Welded Pipe
• B676-03(2009) Standard Specification for UNS N08367 Welded Tube
• B677-05 Standard Specification for UNS N08925, UNS N08354, and UNS N08926 Seamless Pipe and Tube
• B678-86(2006) Standard Test Method for Solderability of Metallic-Coated Products
• B679-98(2004)e1 Standard Specification for Electrodeposited Coatings of Palladium for Engineering Use
• B680-80(2004) Standard Test Method for Seal Quality of Anodic Coatings on Aluminum by Acid Dissolution
• B682-01 Standard Specification for Standard Metric Sizes of Electrical Conductors
• B683-01(2006) Standard Specification for Pure Palladium Electrical Contact Material
• B684-97(2008) Standard Specification for Platinum-Iridium Electrical Contact Materials
• B685-01(2006) Standard Specification for Palladium-Copper Electrical Contact Material
• B686/B686M-08 Standard Specification for Aluminum Alloy Castings, High-Strength
• B687-99(2005)e1 Standard Specification for Brass, Copper, and Chromium-Plated Pipe Nipples
• B688-96(2009) Standard Specification for Chromium-Nickel-Molybdenum-Iron (UNS N08366 and UNS N08367) Plate, Sheet, and Strip
• B689-97(2008) Standard Specification for Electroplated Engineering Nickel Coatings
• B690-02(2007) Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube
• B691-02(2007) Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Rod, Bar, and Wire
• B692-90(2006) Standard Specification for 75% Silver-25 % Graphite Sliding Contact Material
• B693-91(2006) Standard Specification for Silver-Nickel Electrical Contact Materials
• B694-03 Standard Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding
• B695-04 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
• B696-00(2004)e1 Standard Specification for Coatings of Cadmium Mechanically Deposited
• B697-88(2005) Standard Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic Coatings
• B698-02 Standard Classification for Seamless Copper and Copper Alloy Plumbing Pipe and Tube
• B699-86(2008) Standard Specification for Coatings of Cadmium Vacuum-Deposited on Iron and Steel
• B700-08 Standard Specification for Electrodeposited Coatings of Silver for Engineering Use
• B701/B701M-06 Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD)
• B702-93(2004) Standard Specification for Copper-Tungsten Electrical Contact Material
• B703-05 Standard Test Method for Apparent Density of Powders Using Arnold Meter
• B704-03 Standard Specification for Welded UNS N06625, UNS N06219 and UNS N08825 Alloy Tubes
• B705-05 Standard Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
• B706-00(2006) Standard Specification for Seamless Copper Alloy (UNS No. C69100) Pipe and Tube
• B708-05 Standard Specification for Tantalum and Tantalum Alloy Plate, Sheet, and Strip
• B709-04(2009) Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028)* Plate, Sheet, and Strip
• B710-04 Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe
• B711-05 Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel Reinforced (AACSR) (6201)
• B712-93(2006) Standard Guide for Determination of Sodium and Potassium Content For Silver-Cadmium Oxide Contact Materials
• B715-96(2001) Standard Specification for Sintered Copper Structural Parts for Electrical Conductivity Applications
• B717-96(2006) Standard Specification for Refined Ruthenium
• B718-00(2006) Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Plate, Sheet, and Strip
• B719-00(2005) Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Bar
• B722-06 Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Seamless Pipe and Tube
• B723-00(2005) Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Welded Pipe
• B724-00(2006) Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Newage, Portable, Non-Caliper-Type Instrument
• B725-05 Standard Specification for Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Pipe
• B726-02(2006) Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Welded Tube
• B727-04 Standard Practice for Preparation of Plastics Materials for Electroplating
• B729-05 Standard Specification for Seamless UNS N08020, UNS N08026, and UNS N08024 Nickel-Alloy Pipe and Tube
• B730-08 Standard Specification for Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Tube
• B731-96(2006) Standard Specification for 60% Palladium-40 % Silver Electrical Contact Material
• B733-04 Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal
• B734-97(2008) Standard Specification for Electrodeposited Copper for Engineering Uses
• B735-06 Standard Test Method for Porosity in Gold Coatings on Metal Substrates by Nitric Acid Vapor
• B736-00(2006) Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock
• B737-05 Standard Specification for Hot-Rolled and/or Cold-Finished Hafnium Rod and Wire
• B738-03(2008) Standard Specification for Fine-Wire Bunch-Stranded and Rope-Lay Bunch-Stranded Copper Conductors for Use as Electrical Conductors
• B739-03(2008) Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Tube
• B740-02 Standard Specification for Copper-Nickel-Tin Spinodal Alloy Strip
• B742-90(2006) Standard Specification for Fine Silver Electrical Contact Fabricated Material
• B743-06 Standard Specification for Seamless Copper Tube in Coils
• B744/B744M-05 Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe
• B745/B745M-97(2005) Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• B746/B746M-02(2007) Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• B747-07 Standard Specification for Copper-Zirconium Alloy Sheet and Strip
• B748-90(2006) Standard Test Method for Measurement of Thickness of Metallic Coatings by Measurement of Cross Section with a Scanning Electron Microscope
• B749-03 Standard Specification for Lead and Lead Alloy Strip, Sheet, and Plate Products
• B750-08 Standard Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
• B751-08 Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Tube
• B752-06 Standard Specification for Castings, Zirconium-Base, Corrosion Resistant, for General Application
• B753-07 Standard Specification for Thermostat Component Alloys
• B754-89(2005) Standard Test Method for Measuring and Recording the Deviations from Flatness in Copper and Copper Alloy Strip
• B755-00(2006) Standard Specification for Nickel-Chromium-Molybdenum-Tungsten Alloys (UNS N06110) Plate, Sheet, and Strip
• B756-00(2006) Standard Specification for Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06110) Rod and Bar
• B757-00(2006) Standard Specification for Nickel-Chromium-Molybdenum-Tungsten-Alloys (UNS N06110) Welded Pipe
• B758-00(2006) Standard Specification for Nickel-Chromium-Molybdenum-Tungsten Alloys (UNS N06110) Welded Tube
• B759-00(2006) Standard Specification for Nickel-Chromium-Molybdenum-Tungsten Alloys (UNS N06110) Pipe and Tube
• B760-07 Standard Specification for Tungsten Plate, Sheet, and Foil
• B761-06 Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation
• B762-90(2005) Standard Test Method of Variables Sampling of Metallic and Inorganic Coatings
• B763-08a Standard Specification for Copper Alloy Sand Castings for Valve Applications
• B764-04 Standard Test Method for Simultaneous Thickness and Electrode Potential Determination of Individual Layers in Multilayer Nickel Deposit (STEP Test)
• B765-03(2008) Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings
• B766-86(2008) Standard Specification for Electrodeposited Coatings of Cadmium
• B767-88(2006) Standard Guide for Determining Mass Per Unit Area of Electrodeposited and Related Coatings by Gravimetric and Other Chemical Analysis Procedures
• B768-99(2004) Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Strip and Sheet
• B769-07 Standard Test Method for Shear Testing of Aluminum Alloys
• B770-08 Standard Specification for Copper-Beryllium Alloy Sand Castings for General Applications
• B771-87(2006) Standard Test Method for Short Rod Fracture Toughness of Cemented Carbides
• B772-97(2008) Standard Guide for Specifying the Chemical Compositions for Electrical Contact Materials (Arcing and Nonarcing)
• B773-96(2008) Standard Guide for Ultrasonic C-Scan Bond Evaluation of Brazed or Welded Electrical Contact Assemblies
• B774-00(2005)e1 Standard Specification for Low Melting Point Alloys
• B775-08 Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
• B776-07 Standard Specification for Hafnium and Hafnium Alloy Strip, Sheet, and Plate
• B777-07 Standard Specification for Tungsten Base, High-Density Metal
• B778-02(2007) Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors (AAC/TW)
• B779-03 Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Steel-Reinforced (ACSR/TW)
• B780-98(2004) Standard Specification for 75% Silver, 24.5% Copper, 0.5% Nickel Electrical Contact Alloy
• B781-93a(2006) Standard Guide for Silver-Cadmium Oxide Contact Material
• B783-04 Standard Specification for Materials for Ferrous Powder Metallurgy (P/M) Structural Parts
• B784-01(2006) Standard Specification for Modified Concentric-Lay-Stranded Copper Conductors for Use in Insulated Electrical Cables
• B786-08 Standard Specification for 19 Wire Combination Unilay-Stranded Aluminum Conductors for Subsequent Insulation
• B787/B787M-04 Standard Specification for 19 Wire Combination Unilay-Stranded Copper Conductors for Subsequent Insulation
• B788/B788M-04 Standard Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe
• B789/B789M-99(2005) Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
• B790/B790M-00(2006) Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
• B792-08 Standard Specification for Zinc Alloys in Ingot Form for Slush Casting
• B793-08 Standard Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds
• B794-97(2009) Standard Test Method for Durability Wear Testing of Separable Electrical Connector Systems Using Electrical Resistance Measurements
• B795-07 Standard Test Method for Determining the Percentage of Alloyed or Unalloyed Iron Contamination Present in Powder Forged (PF) Steel Materials
• B796-07 Standard Test Method for Nonmetallic Inclusion Content of Powders Intended for Powder Forging (PF) Applications
• B797-93(2007) Standard Test Method for Surface Finger Oxide Penetration Depth and Presence of Interparticle Oxide Networks in Powder Forged (P/F) Steel Parts
• B798-95(2005) Standard Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography
• B799-95(2005) Standard Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor
• B800-05 Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical Purposes-Annealed and Intermediate Tempers
• B801-07 Standard Specification for Concentric-Lay-Stranded Conductors of 8000 Series Aluminum Alloy for Subsequent Covering or Insulation
• B802/B802M-08 Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors, Steel Reinforced (ACSR)
• B803-08 Standard Specification for High-Strength Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors
• B804-02(2007) Standard Specification for UNS N08367 and UNS N08926 Welded Pipe
• B805-06 Standard Specification for Precipitation Hardening Nickel Alloys Bar and Wire
• B806-08a Standard Specification for Copper Alloy Permanent Mold Castings for General Applications
• B806-08a Standard Specification for Copper Alloy Permanent Mold Castings for General Applications CHINESE TRANSLATION
• B807/B807M-06 Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys
• B808-05 Standard Test Method for Monitoring of Atmospheric Corrosion Chambers by Quartz Crystal Microbalances
• B809-95(2008) Standard Test Method for Porosity in Metallic Coatings by Humid Sulfur Vapor (「Flowers-of-Sulfur」
• B810-01a(2006) Standard Test Method for Calibration of Atmospheric Corrosion Test Chambers by Change in Mass of Copper Coupons
• B811-02(2007) Standard Specification for Wrought Zirconium Alloy Seamless Tubes for Nuclear Reactor Fuel Cladding
• B812-96(2008) Standard Test Method for Resistance to Environmental Degradation of Electrical Pressure Connections Involving Aluminum and Intended for Residential Applications
• B813-00(2009) Standard Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
• B814-06 Standard Specification for Nickel-Chromium-Iron-Molybdenum-Tungsten Alloy (UNS N06920) Plate, Sheet, and Strip
• B815-02(2006) Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Rod
• B816-00(2004)e1 Standard Specification for Coatings of Cadmium-Zinc Mechanically Deposited
• B817-08 Standard Specification for Powder Metallurgy (P/M) Titanium Alloy Structural Components
• B818-03(2008) Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Plate, Sheet and Strip
• B819-00(2006) Standard Specification for Seamless Copper Tube for Medical Gas Systems
• B820-09 Standard Test Method for Bend Test for Determining the Formability of Copper and Copper Alloy Strip
• B821-02(2007) Standard Guide for Liquid Dispersion of Metal Powders and Related Compounds for Particle Size Analysis
• B822-02 Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by Light Scattering
• B823-01 Standard Specification for Materials for Nonferrous Powder Metallurgy (P/M) Structural Parts
• B824-09 Standard Specification for General Requirements for Copper Alloy Castings
• B824-04 Standard Specification for General Requirements for Copper Alloy Castings CHINESE TRANSLATION
• B825-02(2008) Standard Test Method for Coulometric Reduction of Surface Films on Metallic Test Samples
• B826-03 Standard Test Method for Monitoring Atmospheric Corrosion Tests by Electrical Resistance Probes
• B827-05 Standard Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests
• B828-02 Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings
• B829-04a(2009) Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
• B830-97(2003) Standard Specification for Uniform Test Methods and Frequency
• B831-05 Standard Test Method for Shear Testing of Thin Aluminum Alloy Products
• B832-93(2008) Standard Guide for Electroforming with Nickel and Copper
• B833-06 Standard Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel
• B834-95(2003) Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367) and Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625) Alloy Pipe Flanges, Fittings, Valves, and Parts
• B835-04 Standard Specification for Compact Round Stranded Copper Conductors Using Single Input Wire Construction
• B836-00(2005) Standard Specification for Compact Round Stranded Aluminum Conductors Using Single Input Wire Construction
• B837-01 Standard Specification for Seamless Copper Tube for Natural Gas and Liquefied Petroleum (LP) Gas Fuel Distribution Systems
• B839-04 Standard Test Method for Residual Embrittlement in Metallic Coated, Externally Threaded Articles, Fasteners, and Rod—Inclined Wedge Method
• B840-99(2004) Standard Specification for Electrodeposited Coatings for Zinc Cobalt Alloy Deposits
• B841-99(2004) Standard Specification for Electrodeposited Coatings for Zinc Nickel Alloy Deposits
• B842-99(2005) Standard Specification for Electrodeposited Coatings for Zinc Iron Alloy Deposits
• B843-07 Standard Specification for Magnesium Alloy Anodes for Cathodic Protection
• B844-98(2004) Standard Guide for Silver-Tin Oxide Contact Material
• B845-97(2008)e1 Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts
• B846-06a Standard Terminology for Copper and Copper Alloys
• B846-06a Standard Terminology for Copper and Copper Alloys CHINESE TRANSLATION
• B848-05 Specification for Powder Forged (P/F) Ferrous Materials
• B849-02(2007) Standard Specification for Pre-Treatments of Iron or Steel for Reducing Risk of Hydrogen Embrittlement
• B850-98(2004) Standard Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement
• B851-04 Standard Specification for Automated Controlled Shot Peening of Metallic Articles Prior to Nickel, Autocatalytic Nickel, or Chromium Plating, or as Final Finish
• B852-08 Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel
• B853-07 Standard Specification for Powder Metallurgy (PM) Boron Stainless Steel Structural Components
• B854-98(2004) Standard Guide for Measuring Electrical Contact Intermittences
• B855-06 Standard Test Method for Volumetric Flow Rate of Metal Powders Using Arnold Meter and Hall Funnel
• B856-03 Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated Steel Supported (ACSS)
• B857-09 Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Supported (ACSS/TW)
• B858-06 Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys
• B859-03(2008)e1 Standard Practice for De-Agglomeration of Refractory Metal Powders and Their Compounds Prior to Particle Size Analysis
• B860-09 Standard Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing
• B861-08a Standard Specification for Titanium and Titanium Alloy Seamless Pipe
• B862-09 Standard Specification for Titanium and Titanium Alloy Welded Pipe
• B863-09 Standard Specification for Titanium and Titanium Alloy Wire
• B864/B864M-08 Standard Specification for Corrugated Aluminum Box Culverts
• B865-04 Standard Specification for Precipitation Hardening Nickel-Copper-Aluminum Alloy (UNS N05500) Bar, Rod, Wire, Forgings, and Forging Stock
• B866-95(2008) Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion
• B867-95(2008) Standard Specification for Electrodeposited Coatings of Palladium-Nickel for Engineering Use
• B868-96(2008) Standard Practice for Contact Performance Classification of Electrical Connection Systems
• B869-07 Standard Specification for Copper-Clad Steel Electrical Conductor for CATV Drop Wire
• B870-08 Standard Specification for Copper-Beryllium Alloy Forgings and Extrusions Alloys (UNS Nos. C17500 and C17510)
• B871-01(2007) Standard Test Method for Tear Testing of Aluminum Alloy Products
• B872-06 Standard Specification for Precipitation-Hardening Nickel Alloys Plate, Sheet, and Strip
• B873-01(2007) Standard Test Method for Measuring Volume of Apparent Density Cup Used in Test Methods B212, B329, and B417
• B874-96(2008) Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process
• B875-96(2008) Standard Specification for Aluminum Diffusion Coating Applied by Pack Cementation Process
• B877-96(2008) Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method
• B878-97(2009) Standard Test Method for Nanosecond Event Detection for Electrical Contacts and Connectors
• B879-97(2008)e1 Standard Practice for Applying Non-Electrolytic Conversion Coatings on Magnesium and Magnesium Alloys
• B880-03(2008) Standard Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
• B881-05 Standard Terminology Relating to Aluminum- and Magnesium- Alloy Products
• B882-05 Specification for Pre-Patinated Copper for Architectural Applications
• B883-05 Standard Specification for Metal Injection Molding (MIM) Ferrous Materials
• B884-05 Standard Specification for Niobium-Titanium Alloy Billets, Bar, and Rod for Superconducting Applications
• B885-09 Standard Test Method for Presence of Foreign Matter on Printed Wiring Board Contacts
• B886-03(2008) Standard Test Method for Determination of Magnetic Saturation (Ms) of Cemented Carbides
• B887-03(2008)e1 Standard Test Method for Determination of Coercivity (Hcs) of Cemented Carbides
• B888-08 Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts
• B890-07 Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
• B891-98(2004) Standard Specification for Seamless and Welded Titanium and Titanium Alloy Condenser and Heat Exchanger Tubes With Integral Fins
• B892-03 Standard Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy in Ingot Form for Die Castings
• B893-98(2008) Standard Specification for Hard-Coat Anodizing of Magnesium for Engineering Applications
• B894-03 Standard Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy Die Castings
• B895-05 Test Methods for Evaluating the Corrosion Resistance of Stainless Steel Powder Metallurgy (P/M) Parts/Specimens by Immersion in a Sodium Chloride Solution
• B896-99(2005) Standard Test Methods for Evaluating Connectability Characteristics of Electrical Conductor Materials
• B897-03 Standard Specification for Configuration of Zinc and Zinc Alloy Jumbo and Block Ingot
• B898-05e1 Standard Specification for Reactive and Refractory Metal Clad Plate
• B899-06 Standard Terminology Relating to Non-ferrous Metals and Alloys
• B900-04 Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies
• B901-04 Standard Specification for Compressed Round Stranded Aluminum Conductors Using Single Input Wire Construction
• B902-04a Standard Specification for Compressed Round Stranded Copper Conductors, Hard, Medium-Hard, or Soft Using Single Input Wire Construction
• B903-00(2005) Standard Specification for Seamless Copper Heat Exchanger Tubes With Internal Enhancement
• B904-00(2004) Standard Specification for Autocatalytic Nickel over Autocatalytic Copper for Electromagnetic Interference Shielding
• B905-00(2005) Standard Test Methods for Assessing the Adhesion of Metallic and Inorganic Coatings by the Mechanized Tape Test
• B906-02(2006) Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
• B907-05 Standard Specification for Zinc, Tin and Cadmium Base Alloys Used as Solders
• B908-03(2008) Standard Practice for the Use of Color Codes for Zinc Casting Alloy Ingot
• B909-00(2006) Standard Guide for Plane Strain Fracture Toughness Testing of Non-Stress Relieved Aluminum Products
• B910/B910M-07 Standard Specification for Annealed Copper-Clad Steel Wire
• B911/B911M-05 Standard Specification for ACSR Twisted Pair Conductor (ACSR/TP)
• B912-02(2008)e1 Standard Specification for Passivation of Stainless Steels Using Electropolishing
• B913-05 Standard Test Method for Evaluation of Crimped Electrical Connections to 16-Gauge and Smaller Diameter Stranded and Solid Conductors
• B914-03(2008) Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel
• B915-01(2007) Standard Test Method for Measuring Static Heat Resistance of Self-Cleaning Oven Coating
• B916-01(2007) Standard Test Method for Adherence of Porcelain Enamel Coatings to Sheet Metal
• B917/B917M-08 Standard Practice for Heat Treatment of Aluminum-Alloy Castings from All Processes
• B918/B918M-09 Standard Practice for Heat Treatment of Wrought Aluminum Alloys
• B919-01(2006) Standard Specification for Welded Copper Heat Exchanger Tubes With Internal Enhancement
• B920-01(2006)e1 Standard Practice for Porosity in Gold and Palladium Alloy Coatings on Metal Substrates by Vapors of Sodium Hypochlorite Solution
• B921-08 Standard Specification for Non-hexavalent Chromium Conversion Coatings on Aluminum and Aluminum Alloys
• B922-02(2008) Standard Test Method for Metal Powder Specific Surface Area by Physical Adsorption
• B923-02(2008) Standard Test Method for Metal Powder Skeletal Density by Helium or Nitrogen Pycnometry
• B924-02(2006) Standard Specification for Seamless and Welded Nickel Alloy Condenser and Heat Exchanger Tubes With Integral Fins
• B925-08 Standard Practices for Production and Preparation of Powder Metallurgy (PM) Test Specimens
• B926-03 Standard Method for Pinhole Determination in Aluminum and Aluminum Alloy Plain Foil by Means of a Light Table
• B927/B927M-08a Standard Specification for Brass Rod, Bar, and Shapes
• B928/B928M-07 Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service and Similar Environments
• B929-05 Standard Specification for Copper-Nickel-Tin Spinodal Alloy Rod and Bar
• B930-03(2008) Standard Test Method for Rating Grain Size and Frequency of Abnormally Large Grains in Cemented Tungsten Carbides (Hardmetals)
• B931-09 Standard Test Method for Metallographically Estimating the Observed Case Depth of Ferrous Powder Metallurgy (P/M) Parts
• B932-04 Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum-Gadolinium Alloy Plate, Sheet, and Strip
• B933-09 Standard Test Method for Microindentation Hardness of Powder Metallurgy (P/M) Materials
• B934-04a Standard Test Method for Effective Case Depth of Ferrous Powder Metallurgy (P/M) Parts Using Microindentation Hardness Measurements
• B935-05 Standard Guide for Steam Treatment of Ferrous Powder Metallurgy (P/M) Materials
• B936-08 Standard Specification for Copper-Chromium-Iron-Titanium Alloy Plate, Sheet, Strip and Rolled Bar
• B937-04 Standard Specification for Copper-Beryllium Seamless Tube (UNS Nos. C17500 and C17510)
• B938-04 Standard Specification for Copper-Beryllium Alloy Forgings and Extrusions (UNS Nos. C17500 and C17510)
• B939-05 Standard Test Method for Radial Crushing Strength, K, of Powder Metallurgy (P/M) Bearings and Structural Materials
• B940-05 Standard Practice for Testing Non-Chromate Coatings on Zinc and Cadmium Surfaces
• B941-05 Standard Specification for Heat Resistant Aluminum-Zirconium Alloy Wire for Electrical Purposes
• B942-05 Standard Guide for Specification and Quality Assurance for the Electrical Contact Performance of Crimped Wire Terminations
• B943-05 Standard Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications
• B944-06 Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510)
• B945-06 Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10-Type Tempers
• B946-06 Standard Test Method for Surface Finish of Powder Metallurgy (P/M) Products
• B947-06 Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate
• B949-08 Standard Specification for General Requirements for Zinc and Zinc Alloy Products
• B950-06 Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys
• B951-08 Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought
• B952-08 Standard Specification for Zinc Alloys in Ingot Form for Spin Casting
• B953-07 Standard Practice for Sampling Magnesium and Magnesium Alloys for Spectrochemical Analysis
• B954-07 Standard Test Method for Analysis of Magnesium and Magnesium Alloys by Atomic Emission Spectrometry
• B955/B955M-08 Standard Specification for Aluminum-Alloy Centrifugal Castings
• B956-07e2 Standard Specification for Welded Copper and Copper-Alloy Condenser and Heat Exchanger Tubes with Integral Fins
• B957-08 Standard Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Overhead Electrical Conductors
• B958-08 Standard Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors
• B960-08 Standard Specification for Prime Western Grade-Recycled (PWG-R) Zinc
• B961-08 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application
• B962-08 Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products Using Archimedes' Principle
• B963-08 Standard Test Methods for Oil Content, Oil-Impregnation Efficiency, and Interconnected Porosity of Sintered Powder Metallurgy (PM) Products Using Archimedes' Principle
• B964-09 Standard Test Methods for Flow Rate of Metal Powders Using the Carney Funnel
• B965-09 Standard Specification for High Performance Tin-Coated Annealed Copper Wire Intended for Electrical and Electronic Application for Solderability
• B967/B967M-09 Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire

C

• ASTM C 91 Cement Standards and Concrete Standards
• ASTM C 91 - 05 Standard Specification for Masonry Cement
• ASTM C 150 Standard Specification for Portland Cement
• ASTM C 876 Standard Test Method for Half-Cell Potential of uncoated reinforcing steel in concrete
• ASTM C-857-12a Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures
• ASTM C 1112 Standard Guide for Application of Radiation Monitors to the Control and Physical Security of Special Nuclear Material
• ASTM C 1202 Standard Test Method for Electrical Indication of Chloride's Ability to Resist Chloride Ion Penetration
• ASTM C 1270 Standard Practice for Detection Sensitivity Mapping of In-Plant Walk-Through Metal Detectors
• ASTM C 1321 - 04 Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction
• ASTM C 1349 Standard Specification for Architectural Flat Glass Clad Polycarbonate

D

• ASTM D86 Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure
• ASTM D149 Dielectric Strength
• ASTM D256 Impact Strength
• ASTM D4123-82(1995) Standard Test Method for Indirect Tension Test for Resilient Modulus of Bituminous Mixtures
• ASTM D531 -00(2010) Standard Test Method for Rubber Property-Pusey and Jones Indentation
• ASTM D543 Chemical Resistance
• ASTM D570 Water Absorption
• ASTM D1056 Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber
• ASTM D1044 Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion
• ASTM D1457 Elongation
• ASTM D1708 Tensile Strength
• ASTM D1746 Standard Test Method for Transparency of Plastic Sheeting
• ASTM D1894 Coefficient of Friction
• ASTM D2240 Hardness
• ASTM D3786 Bursting strength for Knit fabric and non woven material
• ASTM D4236 - 94(2005) Standard Practice for Labeling Art Materials for Chronic Health Hazards
• ASTM D4356 Standard Practice for Establishing Consistent Test Method Tolerances
• ASTM D5116 Standard Guide for Small-Scale Environmental Chamber Determinations of Organic Emissions From Indoor Materials/Products
• ASTM D5162-08 Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates
• ASTM D5375 Standard Test Methods for Liner removal at High Speeds from Pressure-Sensitive Label Stock
• ASTM D5800 Standard Test Method for Evaporation Loss of Lubricating Oils by the Noack Method
• ASTM D6252 Standard Test Method for Peel Adhesion of Pressure Sensitive Label Stocks at 90 deg Angle
• ASTM D6712 Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes
• ASTM D6751
• ASTM D7240
• ASTM D7298-06 Standard Test Method for Measurement of Comparative Legibility by Means of Polarizing Filter Instrumentation
• ASTM D7483 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
• ASTM D7547 Aviation fuel U91

E

• ASTM E8 Standard Test Methods for Tension Testing of Metallic Materials
• ASTM E18 Test Methods for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials
• ASTM E21 Test Methods for Elevated Temperature Tension Tests of Metallic Materials
• ASTM E31 Healthcare Informatics
• ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
• ASTM E96 Standard Test Methods for Water Vapor Transmission of Materials
• ASTM E112 Test Methods for Determining Average Grain Size
• ASTM E119 Standard Test Methods for Fire Tests of Building Construction and Materials
• ASTM E139 Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
• ASTM E150 Practice for Conducting Creep and Creep-Rupture Tension Tests of Metallic Materials Under Conditions of Rapid Heating and Short Times
• ASTM E151 Practice for Tension Tests of Metallic Materials at Elevated Temperatures with Rapid Heating and Conventional or Rapid Strain Rates
• ASTM E290 Standard Test Methods for Bend Testing of Material for Ductility
• ASTM E292 Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials
• ASTM E328 Methods for Stress-Relaxation Tests for Materials and Structures
• ASTM E381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
• ASTM E460 Practice for Determining Effect of Packaging on Food and Beverage Products During Storage
• ASTM E566 Practice for Electromagnetic (Eddy-Current) Sorting of Ferrous Metals
• ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
• ASTM E779 Standard Test Method for Determining Air Leakage Rate by Fan Pressurization
• ASTM E1417 Standard Practice for Liquid Penetrant Testing
• ASTM E1444 Standard Practice for Magnetic Particle Testing
• ASTM E1155 Standard Test Method for Determining F_F Flatness and F_L Levelness Numbers, pertaining primarily to cast-in-place concrete floors
• ASTM E1169 Standard Guide for Conducting Ruggedness Tests
• ASTM E1316: "Standard Terminology for Nondestructive Examinations"
• ASTM E1488 Standard Guide for Statistical Procedures to Use in Developing and Applying Test Methods
• ASTM E1558 Standard Guide for Electrolytic Polishing of Metallographic Specimens
• ASTM E1714
• ASTM E1751 Standard Guide for Temperature Electromotive Force (emf) Tables for Non-Letter Designated Thermocouple Combinations
• ASTM E1870 Test Method for Odor and Taste Transfer from Polymeric Packaging Film
• ASTM E2395
• ASTM E2500 Standard Guide for Specification, Design, and Verification of Pharmaceutical and Biopharmaceutical Manufacturing Systems and Equipment

F

• ASTM F86 Standard Practice for Surface Preparation and Marking of Metallic Surgical Implants
• ASTM F136 Standard Specification for Wrought Titanium-6 Aluminum-4 Vanadium ELI (Extra Low Interstitial) Alloy for Surgical Implant Applications
• ASTM F432 Standard Specification for Roof and Rock Bolts and Accessories
• ASTM F436 Standard Specification for Hardened Steel Washers
• ASTM F436M Standard Specification for Hardened Steel Washers (Metric)
• ASTM F568M Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners. Withdrawn January 2012 due to ISO 898-1.
• ASTM F 571
• ASTM F 606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets
• ASTM F 626
• ASTM F 883
• ASTM F 963 Standard Consumer Safety Specification for Toy Safety.
• ASTM F 1450
• ASTM F 1577
• ASTM F 1592
• ASTM F 1643
• ASTM F 1712
• ASTM F 1915
• ASTM F 1929 Standard Test Method for Detecting Seal Leaks in Porous Medical Packaging by Dye Penetration
• ASTM F 2248
• ASTM F 2322
• ASTM F 2348
• ASTM F 2412 - 05 Standard Test Methods for Foot Protection.
• ASTM F 2413 - 05 Standard Specification for Performance Requirements for Foot Protection.
• ASTM F 2761 - 09 Essential safety requirements for equipment comprising the patient-centric integrated clinical environment (ICE) — Part 1: General requirements and conceptual model

G

• G1 Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
• G2 Standard Test Method for Corrosion Testing of Products of Zirconium, Hafnium, and Their Alloys in Water at 680°F [360°C]or in Steam at 750°F [400°C]
• G3 Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing
• G4 Standard Guide for Conducting Corrosion Tests in Field Applications
• G5 Standard Reference Test Method for Making Potentiostatic and Potentiodynamic Anodic Polarization Measurements
• G6 Test Method for Abrasion Resistance of Pipeline Coatings
• G7 Standard Practice for Atmospheric Environmental Exposure Testing of Nonmetallic Materials
• G8 Standard Test Methods for Cathodic Disbonding of Pipeline Coatings
• G9 Standard Test Method for Water Penetration into Pipeline Coatings
• G10 Standard Test Method for Specific Bendability of Pipeline Coatings
• G11 Standard Test Method for Effects of Outdoor Weathering on Pipeline Coatings
• G12 Standard Test Method for Nondestructive Measurement of Film Thickness of Pipeline Coatings on Steel
• G14 Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)
• G15 Standard Terminology Relating to Corrosion and Corrosion Testing
• G16 Standard Guide for Applying Statistics to Analysis of Corrosion Data
• G17 Standard Test Method for Penetration Resistance of Pipeline Coatings (Blunt Rod)
• G18 Standard Test Method for Joints, Fittings, and Patches in Coated Pipelines
• G19 Standard Test Method for Disbonding Characteristics of Pipeline Coatings by Direct Soil Burial
• G20 Standard Test Method for Chemical Resistance of Pipeline Coatings
• G21 Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
• G24 Standard Practice for Conducting Exposures to Daylight Filtered Through Glass
• G28 Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys
• G29 Standard Practice for Determining Algal Resistance of Plastic Films
• G30 Standard Practice for Making and Using U-Bend Stress-Corrosion Test Specimens
• G31 Standard Practice for Laboratory Immersion Corrosion Testing of Metals
• G32 Standard Test Method for Cavitation Erosion Using Vibratory Apparatus
• G33 Standard Practice for Recording Data from Atmospheric Corrosion Tests of Metallic-Coated Steel Specimens
• G34 Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test)
• G35 Standard Practice for Determining the Susceptibility of Stainless Steels and Related Nickel-Chromium-Iron Alloys to Stress-Corrosion Cracking in Polythionic Acids
• G36 Standard Practice for Evaluating Stress-Corrosion-Cracking Resistance of Metals and Alloys in a Boiling Magnesium Chloride Solution
• G37 Standard Practice for Use of Mattsson's Solution of pH 7.2 to Evaluate the Stress- Corrosion Cracking Susceptibility of Copper-Zinc Alloys
• G38 Standard Practice for Making and Using C-Ring Stress-Corrosion Test Specimens
• G39 Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens
• G40 Standard Terminology Relating to Wear and Erosion
• G41 Standard Practice for Determining Cracking Susceptibility of Metals Exposed Under Stress to a Hot Salt Environment
• G42 Standard Test Method for Cathodic Disbonding of Pipeline Coatings Subjected to Elevated Temperatures
• G44 Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5% Sodium Chloride Solution
• G46 Standard Guide for Examination and Evaluation of Pitting Corrosion
• G47 Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products
• G48 Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution
• G49 Standard Practice for Preparation and Use of Direct Tension Stress-Corrosion Test Specimens
• G50 Standard Practice for Conducting Atmospheric Corrosion Tests on Metals
• G51 Standard Test Method for Measuring pH of Soil for Use in Corrosion Testing
• G52 Standard Practice for Exposing and Evaluating Metals and Alloys in Surface Seawater
• G55 Standard Test Method for Evaluating Pipeline Coating Patch Materials
• G56 Standard Test Method for Abrasiveness of Ink-Impregnated Fabric Printer Ribbons
• G57 Standard Test Method for Field Measurement of Soil Resistivity Using the Wenner Four-Electrode Method
• G58 Standard Practice for Preparation of Stress-Corrosion Test Specimens for Weldments
• G59 Standard Test Method for Conducting Potentiodynamic Polarization Resistance Measurements
• G60 Standard Practice for Conducting Cyclic Humidity Exposures
• G61 Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys
• G62 Standard Test Methods for Holiday Detection in Pipeline Coatings
• G63 Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service
• G64 Standard Classification of Resistance to Stress-Corrosion Cracking of Heat-Treatable Aluminum Alloys
• G65 Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus
• G66 Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test)
• G67 Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
• G69 Standard Test Method for Measurement of Corrosion Potentials of Aluminum Alloys
• G70 Standard Test Method for Ring Bendability of Pipeline Coatings (Squeeze Test)
• G71 Standard Guide for Conducting and Evaluating Galvanic Corrosion Tests in Electrolytes
• G72 Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment
• G73 Standard Practice for Liquid Impingement Erosion Testing
• G74 Standard Test Method for Ignition Sensitivity of Materials to Gaseous Fluid Impact
• G75 Standard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number)
• G76 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets
• G77 Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test
• G78 Standard Guide for Crevice Corrosion Testing of Iron-Base and Nickel-Base Stainless Alloys in Seawater and Other Chloride-Containing Aqueous Environments
• G80 Standard Test Method for Specific Cathodic Disbonding of Pipeline Coatings
• G81 Standard Test Method for Jaw Crusher Gouging Abrasion Test
• G82 Standard Guide for Development and Use of a Galvanic Series for Predicting Galvanic Corrosion Performance
• G84 Standard Practice for Measurement of Time-of-Wetness on Surfaces Exposed to Wetting Conditions as in Atmospheric Corrosion Testing
• G85 Standard Practice for Modified Salt Spray (Fog) Testing
• G86 Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments
• G87 Standard Practice for Conducting Moist SO2 Tests
• G88 Standard Guide for Designing Systems for Oxygen Service
• G90 Standard Practice for Performing Accelerated Outdoor Weathering of Nonmetallic Materials Using Concentrated Natural Sunlight
• G91 Standard Practice for Monitoring Atmospheric SO2 Using the Sulfation Plate Technique
• G92 Standard Practice for Characterization of Atmospheric Test Sites
• G93 Standard Practice for Cleaning Methods and Cleanliness Levels for Material and Equipment Used in Oxygen-Enriched Environments
• G94 Standard Guide for Evaluating Metals for Oxygen Service
• G95 Standard Test Method for Cathodic Disbondment Test of Pipeline Coatings (Attached Cell Method)
• G96 Standard Guide for Online Monitoring of Corrosion in Plant Equipment (Electrical and Electrochemical Methods)
• G97 Standard Test Method for Laboratory Evaluation of Magnesium Sacrificial Anode Test Specimens for Underground Applications
• G98 Standard Test Method for Galling Resistance of Materials
• G99 Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus
• G100 Standard Test Method for Conducting Cyclic Galvanostaircase Polarization
• G101 Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
• G102 Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements
• G103 Standard Practice for Evaluating Stress-Corrosion Cracking Resistance of Low Copper 7XXX Series Al-Zn-Mg-Cu Alloys in Boiling 6% Sodium Chloride Solution
• G105 Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests
• G106 Standard Practice for Verification of Algorithm and Equipment for Electrochemical Impedance Measurements
• G107 Standard Guide for Formats for Collection and Compilation of Corrosion Data for Metals for Computerized Database Input
• G108 Standard Test Method for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels
• G109 Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments
• G110 Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatable Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution
• G111 Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both
• G112 Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys
• G113 Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials
• G114 Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service
• G115 Standard Guide for Measuring and Reporting Friction Coefficients
• G116 Standard Practice for Conducting Wire-on-Bolt Test for Atmospheric Galvanic Corrosion
• G117 Standard Guide for Calculating and Reporting Measures of Precision Using Data from Interlaboratory Wear or Erosion Tests
• G118 Standard Guide for Recommended Format of Wear Test Data Suitable for Databases
• G119 Standard Guide for Determining Synergism Between Wear and Corrosion
• G120 Standard Practice for Determination of Soluble Residual Contamination in by Soxhlet Extraction
• G121 Standard Practice for Preparation of Contaminated Test Coupons for the Evaluation of Cleaning Agents
• G122 Standard Test Method for Evaluating the Effectiveness of Cleaning Agents
• G123 Standard Test Method for Evaluating Stress-Corrosion Cracking of Stainless Alloys with Different Nickel Content in Boiling Acidified Sodium Chloride Solution
• G124 Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen-Enriched Atmospheres
• G125 Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants
• G126 Standard Terminology Relating to the Compatibility and Sensitivity of Materials in Oxygen Enriched Atmospheres
• G127 Standard Guide for the Selection of Cleaning Agents for Oxygen Systems
• G128 Standard Guide for Control of Hazards and Risks in Oxygen Enriched Systems
• G129 Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking
• G130 Standard Test Method for Calibration of Narrow- and Broad-Band Ultraviolet Radiometers Using a Spectroradiometer
• G131 Standard Practice for Cleaning of Materials and Components by Ultrasonic Techniques
• G132 Standard Test Method for Pin Abrasion Testing
• G133 Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
• G134 Standard Test Method for Erosion of Solid Materials by a Cavitating Liquid Jet
• G135 Standard Guide for Computerized Exchange of Corrosion Data for Metals
• G136 Standard Practice for Determination of Soluble Residual Contaminants in Materials by Ultrasonic Extraction
• G137 Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
• G138 Standard Test Method for Calibration of a Spectroradiometer Using a Standard Source of Irradiance
• G139 Standard Test Method for Determining Stress-Corrosion Cracking Resistance of Heat-Treatable Aluminum Alloy Products Using Breaking Load Method
• G140 Standard Test Method for Determining Atmospheric Chloride Deposition Rate by Wet Candle Method
• G141 Standard Guide for Addressing Variability in Exposure Testing on Nonmetallic Materials
• G142 Standard Test Method for Determination of Susceptibility of Metals to Embrittlement in Hydrogen Containing Environments at High Pressure, High Temperature, or Both
• G143 Standard Test Method for Measurement of Web/Roller Friction Characteristics
• G144 Standard Test Method for Determination of Residual Contamination of Materials and Components by Total Carbon Analysis Using a High Temperature Combustion Analyzer
• G145 Standard Guide for Studying Fire Incidents in Oxygen Systems
• G146 Standard Practice for Evaluation of Disbonding of Bimetallic Stainless Alloy/Steel Plate for Use in High-Pressure, High-Temperature Refinery Hydrogen Service
• G147 Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
• G148 Standard Practice for Evaluation of Hydrogen Uptake, Permeation, and Transport in Metals by an Electrochemical Technique
• G150 Standard Test Method for Electrochemical Critical Pitting Temperature Testing of Stainless Steels
• G151 Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
• G152 Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
• G153 Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
• G154 Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
• G155 Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
• G156 Standard Practice for Selecting and Characterizing Weathering Reference Materials Used to Monitor Consistency of Conditions in an Exposure Test
• G157 Standard Guide for Evaluating the Corrosion Properties of Wrought Iron- and Nickel-Based Corrosion Resistant Alloys for the Chemical Process Industries
• G158 Standard Guide for Three Methods of Assessing Buried Steel Tanks
• G160 Standard Practice for Evaluating Microbial Susceptibility of Nonmetallic Materials by Laboratory Soil Burial
• G161 Standard Guide for Corrosion-Related Failure Analysis
• G162 Standard Practice for Conducting and Evaluating Laboratory Corrosions Tests in Soils
• G163 Standard Guide for Digital Data Acquisition in Wear and Friction Measurements
• G164 Standard Test Method for Determination of Surface Lubrication on Flexible Webs
• G165 Standard Practice for Determining Rail-to-Earth Resistance
• G166 Standard Guide for Statistical Analysis of Service Life Data
• G167 Standard Test Method for Calibration of a Pyranometer Using a Pyrheliometer
• G168 Standard Practice for Making and Using Precracked Double Beam Stress Corrosion Specimens
• G169 Standard Guide for Application of Basic Statistical Methods to Weathering Tests
• G170 Standard Guide for Evaluating and Qualifying Oilfield and Refinery Corrosion Inhibitors in the Laboratory
• G171 Standard Test Method for Scratch Hardness of Materials Using a Diamond Stylus
• G172 Standard Guide for Statistical Analysis of Accelerated Service Life Data
• G173 Standard Tables for Reference Solar Spectral Irradiances: Direct Normal and Hemispherical on 37° Tilted Surface
• G174 Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact
• G175 Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Regulators Used for Medical and Emergency Applications
• G176 Standard Test Method for Ranking Resistance of Plastics to Sliding Wear using Block-on-Ring Wear Test—Cumulative Wear Method
• G177 Standard Tables for Reference Solar Ultraviolet Spectral Distributions: Hemispherical on 37° Tilted Surface
• G178 Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique
• G179 Standard Specification for Metal Black Panel and White Panel Temperature Devices for Natural Weathering Tests
• G180 Standard Test Method for Initial Screening of Corrosion Inhibiting Admixtures for Steel in Concrete
• G181 Standard Practice for Conducting Friction Tests of Piston Ring and Cylinder Liner Materials Under Lubricated Conditions
• G182 Standard Test Method for Determination of the Breakaway Friction Characteristics of Rolling Element Bearings
• G183 Standard Practice for Field Use of Pyranometers, Pyrheliometers and UV Radiometers
• G184 Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using Rotating Cage
• G185 Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using the Rotating Cylinder Electrode
• G186 Standard Test Method for Determining Whether Gas-Leak-Detector Fluid Solutions Can Cause Stress Corrosion Cracking of Brass Alloys
• G187 Standard Test Method for Measurement of Soil Resistivity Using the Two-Electrode Soil Box Method
• G188 Standard Specification for Leak Detector Solutions Intended for Use on Brasses and Other Copper Alloys
• G189 Standard Guide for Laboratory Simulation of Corrosion Under Insulation
• G190 Standard Guide for Developing and Selecting Wear Tests
• G192 Standard Test Method for Determining the Crevice Repassivation Potential of Corrosion-Resistant Alloys Using a Potentiodynamic-Galvanostatic-Potentiostatic Technique
• G194 Standard Test Method for Measuring Rolling Friction Characteristics of a Spherical Shape on a Flat Horizontal Plane
• G195 Standard Guide for Conducting Wear Tests Using a Rotary Platform, Double-Head Abraser
• G196 Standard Test Method for Galling Resistance of Material Couples
• G197 Standard Table for Reference Solar Spectral Distributions: Direct and Diffuse on 20° Tilted and Vertical Surfaces
• G199 Standard Guide for Electrochemical Noise Measurement